vdmr10a1, VDMO10A1, vdmy10a1, vdmg10a1 www.vishay.com vishay semiconductors rev. 1.0, 13-may-13 1 document number: 84197 for technical questions, contact: led@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 standard 7-segment smd display 10 mm description the vdm.10a1 series are 10 mm smd seven segment led displays in a very compact package. the devices utilize alingap on gaas chip technology. product group and package data ? product group: display ?package: 10 mm ? product series: smd ? angle of half intensity: 50 features ? evenly lighted segments ? grey package surface ? untinted segments ? luminous intensity categorized ? yellow, green, and soft orange categorized for color ? wide viewing angle ? suitable for dc and high peak current ? material categorization: for definitions of compliance please see www.vishay.com/doc?99912 applications ?panel meters ? test- and measure-equipment ? point-of-sale terminals ? control units ? parts table part color luminous intensity (cd) at i f (ma) wavelength (nm) at i f (ma) forward voltage (v) at i f (ma) circuitry min. typ. max. min. typ. max. min. typ. max. vdmr10a1 super red 450 1600 - 1 - 631 - 20 - 2.0 2.6 20 common anode VDMO10A1 soft orange 180 650 - 1 - 605 - 20 - 2.0 2.6 20 common anode vdmy10a1 yellow 450 1600 - 1 - 587 - 20 - 2.0 2.6 20 common anode vdmg10a1 green 110 500 - 1 - 572 - 20 - 2.0 2.6 20 common anode absolute maximum ratings (t amb = 25 c, unless otherwise specified) ? vdmr10a1, VDMO10A1, vdmy10a1, vdmg10a1 parameter test condition symbol value unit power dissipa tion per segment p v 70 mw peak forward current per segment ? (frequency 1 khz, 10 % duty cycle) i f 60 ma continous forward current per segment i f 25 ma forward current derating from 25 c 0.28 ma/c operating temperature range t amb - 35 to + 105 c storage temperature range t stg - 35 to + 105 c iron soldering conditions: 1/16" be low seating plane for 3 s at 260 c
vdmr10a1, VDMO10A1, vdmy10a1, vdmg10a1 www.vishay.com vishay semiconductors rev. 1.0, 13-may-13 2 document number: 84197 for technical questions, contact: led@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 notes (1) luminous intensity is measured with a light sensor and filter combination that approximates the cie eye-response curve. (2) reverse voltage is only for ir test.it can not continue to operate at this situation. (3) cross talk specification 2.5 %. notes (1) luminous intensity is measured with a light sensor and filter combination that approximates the cie eye-response curve. (2) reverse voltage is only for ir test.it can not continue to operate at this situation. (3) cross talk specification 2.5 %. notes (1) luminous intensity is measured with a light sensor and filter combination that approximates the cie eye-response curve. (2) reverse voltage is only for ir test.it can not continue to operate at this situation. (3) cross talk specification 2.5 %. optical and electrical characteristics (t amb = 25 c, unless otherwise specified) ? vdmr10a1, super red parameter test condition part symbol min. typ. max. unit luminous intensity (1) i f = 1 ma vdmr10a1 i v 450 1600 - cd i f = 10 ma vdmr10a1 i v - 20 800 - cd dominant wavelength i f = 20 ma vdmr10a1 ? d - 631 - nm peak emmision wavelength i f = 20 ma ? p - 639 - nm spectral line half-width i f = 20 ma ?? -20- forward voltage per segment i f = 20 ma v f -2.02.6v reverse current per segment (2) v r = 5 v i r - - 100 a luminous intensity matching ratio i f = 10 ma i v-m 2:1 optical and electrical characteristics (t amb = 25 c, unless otherwise specified) ? VDMO10A1, soft orange parameter test condition part symbol min. typ. max. unit luminous intensity (1) i f = 1 ma VDMO10A1 i v 180 650 - cd i f = 10 ma VDMO10A1 i v - 8250 - cd dominant wavelength i f = 20 ma VDMO10A1 ? d - 605 - nm peak emmision wavelength i f = 20 ma ? p - 611 - nm spectral line half-width i f = 20 ma ?? -17- forward voltage per segment i f = 20 ma v f -2.02.6v reverse current per segment (2) v r = 5 v i r - - 100 a luminous intensity matching ratio i f = 10 ma i v-m 2:1 optical and electrical characteristics (t amb = 25 c, unless otherwise specified) ? vdmy10a1, yellow parameter test condition part symbol min. typ. max. unit luminous intensity (1) i f = 1 ma vdmy10a1 i v 450 1600 - cd i f = 10 ma vdmy10a1 i v - 17 600 - cd dominant wavelength i f = 20 ma vdmy10a1 ? d - 587 - nm peak emmision wavelength i f = 20 ma ? p - 588 - nm spectral line half-width i f = 20 ma ?? -15- forward voltage per segment i f = 20 ma v f -2.02.6v reverse current per segment (2) v r = 5 v i r - - 100 a luminous intensity matching ratio i f = 10 ma i v-m 2:1
vdmr10a1, VDMO10A1, vdmy10a1, vdmg10a1 www.vishay.com vishay semiconductors rev. 1.0, 13-may-13 3 document number: 84197 for technical questions, contact: led@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 notes (1) luminous intensity is measured with a light sensor and filter combination that approximates the cie eye-response curve. (2) reverse voltage is only for ir test.it can not continue to operate at this situation. (3) cross talk specification 2.5 %. note ? the above type numbers repr esent the order groups which include only a few brightness groups. only one group will be shipped in one tube (the re will be no mixing of two groups in one tube). ? in order to ensure availability, single brightness groups will not be orderable. note ? wavelengths are tested at a current pulse duration of 25 ms. ? ? ? ? ? ? ? ? optical and electrical characteristics (t amb = 25 c, unless otherwise specified) ? vdmg10a1, green parameter test condition part symbol min. typ. max. unit luminous intensity (1) i f = 1 ma vdmg10a1 i v 110 500 - cd i f = 10 ma vdmg10a1 i v - 5500 - cd dominant wavelength i f = 20 ma vdmg10a1 ? d - 572 - nm peak emmision wavelength i f = 20 ma ? p - 571 - nm spectral line half-width i f = 20 ma ?? -15- forward voltage per segment i f = 20 ma v f -2.02.6v reverse current per segment (2) v r = 5 v i r - - 100 a luminous intensity matching ratio i f = 10 ma i v-m 2:1 luminous intensity classification group light intensity (cd) standard min. max. d 110 220 e 180 360 f 280 560 g 450 900 h 700 1400 i 1100 2200 k 1800 3600 l 2800 5600 m 4500 9000 n 7000 14 000 p 11 000 22 000 q 18 000 36 000 r 28 000 56 000 s 45 000 90 000 color classification group soft orange yellow green min. max. min. max. min. max. 1 598 601 581 584 - - 2 600 603 583 586 - - 3 602 605 585 588 562 565 4 604 607 587 590 564 567 5 606 609 589 592 566 569 6 608 611 591 594 568 571 7 ----570573 8 ----572575
vdmr10a1, VDMO10A1, vdmy10a1, vdmg10a1 www.vishay.com vishay semiconductors rev. 1.0, 13-may-13 4 document number: 84197 for technical questions, contact: led@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 typical characteristics (t amb = 25 c, unless otherwise specified) fig. 1 - forward current vs. ambient temperature fig. 2 - relative intensity vs. wavelength fig. 3 - relative luminous intensity vs. forward current fig. 4 - forward current vs. forward voltage fig. 5 - peak current vs. duty cycle t amb - ambient temperature (c) 0 10 20 25 30 0 20 40 60 80 100 120 i f - forward current (ma) 5 15 560 600 640 660 680 - wavelength (nm) 0 0.2 0.4 0.6 0.8 1.2 i rel - relative intensity 1.0 s oft orange s uper red green yellow 620 540 520 580 i f - forward current (ma) 30 0 0.5 1.0 3.0 i - relative luminous intensity vrel 10 0 5 15 20 (normalized to 1 at 10 ma) 25 1.5 2.5 2.0 1 10 100 v f - forward voltage (v) i - forward current (ma) f 3.5 3.0 2.5 2.0 1.5 1.0 110 10 100 100 duty cycle % (frequency 1 khz) i peak - peak current (ma)
vdmr10a1, VDMO10A1, vdmy10a1, vdmg10a1 www.vishay.com vishay semiconductors rev. 1.0, 13-may-13 5 document number: 84197 for technical questions, contact: led@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 package dimensions in millimeters specifications according to din technical drawings dimensions in mm drawing-no.: 6.544-5426.01-4 drawing refers to following types: issue: 1; 22.03.13 vdmr 10a1 vdmo 10a1 vdmy 10a1 vdmg 10a1 9.8 10 6 15 5 1 6 10 13 16 10 0.6 ?1.2 1.9 1.5 0.1 r0.65 2.1 1 0 1 . 2 6 . 2 5.15 5.15 1.84 3.7 ?1.4 ?1.55 ?1.7 ?1.7 0.14 a b c d e f g dp a 764219105 bcdef gdp 3, 8 common anode 10 no. cathode c cathode dp cathode b cathode a common anode cathode f cathode g cathode d cathode e connection 2 1 3 4 5 6 7 8 9 3.65 3.66
vdmr10a1, VDMO10A1, vdmy10a1, vdmg10a1 www.vishay.com vishay semiconductors rev. 1.0, 13-may-13 6 document number: 84197 for technical questions, contact: led@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 tape and reel dimensions in millimeters tape in box
vdmr10a1, VDMO10A1, vdmy10a1, vdmg10a1 www.vishay.com vishay semiconductors rev. 1.0, 13-may-13 7 document number: 84197 for technical questions, contact: led@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 bar code product label (example) a. type of component b. manufacturing plant c. sel - selection code (bin): ? e.g.: j2 = code for luminous intensity group ? 4 = code for color group d. date code year/week e. day code (e.g. 2: tuesday) f. batch no. g. total quantity h. company code ? soldering profile fig. 6 - vishay lead (pb)-free reflow soldering profile (acc. to j-std-020c) recommended solder pad msl label soldering iron (one time only) temperature 300 c max. soldering time 3 s max. 106 37 visha y a h b c d e f g vlme2300-gs08 27 p23 19832 0 50 100 150 200 250 300 0 50 100 150 200 250 300 time (s) temperature (c) 255 240 c 245 c max. 260 c max. 120 s max. 100 s 217 c max. 30 s max. ramp up 3 c/s max. ramp down 6 c/s 255 c 19470-5 ir reflow soldering profile for lead (pb)-free soldering preconditioning acc. to jedec level 3 max. 2 cycles allowed 3 1.65 4 x 1.9 = 7.6 15
legal disclaimer notice www.vishay.com vishay revision: 02-oct-12 1 document number: 91000 disclaimer all product, product specifications and data are subject to change without notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, repres entation or guarantee regarding the suitabilit y of the products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all i mplied warranties, including warra nties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain type s of applications are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular application. it is the customers responsib ility to validate that a particu lar product with the properties descri bed in the product specification is suitable fo r use in a particular application. parameters provided in datasheets and/or specification s may vary in different applications an d performance may vary over time. all operating parameters, including typical pa rameters, must be validated for each customer application by the customers technical experts. product specifications do not expand or otherwise modify vish ays terms and condit ions of purchase, including but not limited to the warranty expressed therein. except as expressly indicate d in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vi shay product could result in personal injury or death. customers using or selling vishay products not expressly indicated for use in such applications do so at their own risk. pleas e contact authorized vishay personnel to ob tain written terms and conditions regarding products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual prope rty rights is granted by this document or by any conduct of vishay. product names and markings noted herein may be trad emarks of their respective owners. material category policy vishay intertechnology, inc. hereby certi fies that all its products that are id entified as rohs-compliant fulfill the definitions and restrictions defined under directive 2011/65/eu of the euro pean parliament and of the council of june 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (eee) - recast, unless otherwis e specified as non-compliant. please note that some vishay documentation may still make reference to rohs directive 2002/95/ ec. we confirm that all the products identified as being compliant to directive 2002 /95/ec conform to directive 2011/65/eu. vishay intertechnology, inc. hereby certifi es that all its products that are identified as ha logen-free follow halogen-free requirements as per jedec js709a stan dards. please note that some vishay documentation may still make reference to the iec 61249-2-21 definition. we co nfirm that all the products identified as being compliant to iec 61249-2-21 conform to jedec js709a standards.
|
